Filters
51 products viewed
Filters
Trim For 3/4" Thermostatic Valve - Use with TVH.4201
Handle Operation - The handle is used to control temperature of water flowing through the outlet. This handle does not control the volume of water flowing through the valve.Cut Out Dimensions - The cut out in wall should be 2.67” X 4.44” which is properly covered by the trim plate. This will ensure that the trim plate will cover the cut-out hole in the wall.Trims - The trims comprise of well finished trim plate and handle. The trim plate is used to cover the wall and has markings for HOT/COLD for temperature control handle. Over the temperature control knob, is an anti-scald temperature stop ring which is a safety feature in this thermostatic value. With the help of this ring, temperature of the water is regulated. Covering this ring is the handle knob which has a push button on the side. To adjust the water temperature, one needs to press this button and move the handle to hot or cold direction. Without pressing it, the user will not be able to rotate the handle to the full HOT position – as an anti-scald prevention mechanism. The anti-scald temperature stop ring should be fitted tightly over the valve (tapping using a rubber mallet might be required during installation) for it to function properly.Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower handles. Collection Serie 230 Style Transitional Warranty Limited Lifetime Warranty. See Warranty page for complete details. Available Finishes: Model# Finish List Price (USD) 230.4201TCP Chrome USD311.00 230.4201TMB Matte Black USD381.00 230.4201TSB Satin Brass PVD USD381.00
$311.00
3/4" Thermostatic Valve With Trim
The TVH.4201 is a ¾” Thermostatic valve with NPT female connections. It has two inlets with integral stop kits and single output. The valve has a flow rate of 13.0 GPM @ 60 PSI. The TVH.4201 does not have water turn off capability and thus must be used with a volume control or diverter valve.Supply Stops - There are two safety stops at each water inlet to prevent water flow in case of installation and repairs.Handle Operation - The handle is used to control temperature of water flowing through the outlet. This handle does not control the volume of water flowing through the valve.As the valve is installed, care should be taken to maintain proper distance from the back of the valve to the surface of finished tile which should be between 2.77” and 3.44”. Also, the valve must be installed vertical and not at an angle. In case, the tile is thicker, or wall is deep, extensions are used for elongating both handles of the valve to ensure proper setting of the trim (length of extensions for TVH.4201 valve is 1.40”). Extension kits comprises of thermostatic handle extension, which can be ordered separately in chrome, brushed nickel, or other special finishes.Cut Out Dimensions - The cut out in wall should be 2.67” X 4.44” which is properly covered by the trim plate. This will ensure that the trim plate will cover the cut-out hole in the wall.Trims - The trims comprise of well finished trim plate and handle. The trim plate is used to cover the wall and has markings for HOT/COLD for temperature control handle. Over the temperature control knob, is an anti-scald temperature stop ring which is a safety feature in this thermostatic value. With the help of this ring, temperature of the water is regulated. Covering this ring is the handle knob which has a push button on the side. To adjust the water temperature, one needs to press this button and move the handle to hot or cold direction. Without pressing it, the user will not be able to rotate the handle to the full HOT position – as an anti-scald prevention mechanism. The anti-scald temperature stop ring should be fitted tightly over the valve (tapping using a rubber mallet might be required during installation) for it to function properly.Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower handles. Collection Serie 230 Style Transitional Warranty Limited Lifetime Warranty. See Warranty page for complete details. Available Finishes: Model# Finish List Price (USD) 230.4201CP Chrome USD704.00 230.4201MB Matte Black USD773.00 230.4201SB Satin Brass PVD USD773.00
$704.00
Trim For Thermostatic Valve
Handle Operation - The bottom handle is used to set the temperature. The top handle is used for water diversion and volume control.Cut Out Dimensions - The cut out in wall should be 7.89 X 1.89 Inches and no more – this will ensure that the trim plate will cover the cut-out hole in the wall.Trims - The trims comprise of a well finished cover plate and handle knobs constructed in solid Brass. Over the temperature control knob, is an anti-scald temperature stop ring which is a safety feature in this thermostatic value. With the help of this ring, temperature of the water is regulated. Covering this ring is the temperature handle knob which has a push button on the side. In order to adjust the water temperature, one needs to press this button and move the handle to hot or cold direction. Without pressing it, the user will not be able to rotate the handle to the full HOT position – as an anti-scald prevention mechanism. The anti-scald temperature stop ring should be fitted tightly over the valve (tapping using a rubber mallet might be required) for it to function properly.Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower handles. Collection Serie 230 Style Transitional Warranty Limited Lifetime Warranty. See Warranty page for complete details. Available Finishes: Model# Finish List Price (USD) 230.4000VTCP Chrome USD430.00 230.4000VTMB Matte Black USD485.00 230.4000VTSB Satin Brass PVD USD485.00
$430.00
3/4" Thermostatic Shower Valve & Trim - 3 Output
The 2780 Series of products from Flusso uses the TVH.2705F Thermostatic valve which features 3/4″ NPT connections and has 3 water outputs [ports] which are operable one at a time without shared port operation. This product meets CAL-Green compliance criteria. The bottom handle sets the temperature. The top handle controls water diversion between the 3 water output ports. Each port has full volume control capability.HORIZONTAL OR VERTICAL INSTALLATION – The TVH.2705F can be installed horizontally or vertically.SUPPLY STOPS – There are two safety stops at each water inlet to prevent water flow in case of installation and repairs.HANDLE OPERATION – The right handle is used to control the temperature of water flowing through the outlet ports. The left handle is used to divert the water between each output port and is= capable of controlling the volume of water from full flow to a trickle.ANTI-SCALD RING – Over the temperature control knob, is an anti-scald temperature stop ring which is a safety feature in this thermostatic value. With the help of this ring, the temperature of the water is regulated. Covering this ring is the handle knob which has a push-button on the side. To adjust the water temperature, one needs to press this button and move the handle to a hot or cold direction. Without pressing it, the user will not be able to rotate the handle to the full HOT position – as an anti-scald prevention mechanism. The anti-scald temperature stop ring should be fitted tightly over the valve (tapping using a rubber mallet might be required) for it to function properly.VALVE INSTALLATION -As the valve is installed, care should be taken to maintain a proper distance from the back of the valve to the finished tile which should be between 2.77″ and 3.44″ inches [Rough In Spec]. Also, the value must be installed straight and not at an angle or upside down. In case, the tile is thicker, or valve installed in the wall is too deep, extension kits are available and can be used for elongating both handles of the valve.CUT OUT DIMENSIONS – The cut out in wall should be 7.89″ x 1.89″ Inches which is properly covered by the trim plate. This will ensure that the trim plate will cover the cut-out hole in the wall.TRIMS – The trims comprise of a well-finished cover plate and handle knobs. The trim plate is used to cover the wall. Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower handles.CARTRIDGE – The TVH.2705F valve can be used with two cartridges. The default cartridge that the valve comes with is the Model # 15100 cartridge which is a 3 output non-shared [CAL-Green Compliant] cartridge. A shared port operation cartridge [Model # 15200] can also be used to activate 2 out of 3 ports at the same time. Collection Serie 230 Style Transitional Warranty Limited Lifetime Warranty. See Warranty page for complete details. Available Finishes: Model# Finish List Price (USD) 230.2780CP Chrome USD1,239.00 230.2780MB Matte Black USD1,294.00 230.2780SB Satin Brass PVD USD1,294.00
$1,239.00
3/4" Thermostatic Shower Valve & Trim - 2-Output
The 2740 series of products from Flusso uses the TVH.2717F Thermostatic valve which features 3/4″ NPT connections and has 2 water outputs [ports] which are operable one at a time without shared port operation. This product meets CAL-Green compliance criteria. The right handle sets the temperature. The left handle controls water diversion between the 2 water output ports. Each port has full volume control capability.HORIZONTAL OR VERTICAL INSTALLATION – The TVH.2717F can be installed horizontally or vertically.SUPPLY STOPS – There are two safety stops at each water inlet to prevent water flow in case of installation and repairs.HANDLE OPERATION – The bottom handle is used to control the temperature of water flowing through the outlet ports. The top handle is used to divert the water between each output port and is= capable of controlling the volume of water from full flow to a trickle.ANTI-SCALD RING – Over the temperature control knob, is an anti-scald temperature stop ring which is a safety feature in this thermostatic value. With the help of this ring, the temperature of the water is regulated. Covering this ring is the handle knob which has a push-button on the side. In order to adjust the water temperature, one needs to press this button and move the handle to a hot or cold direction. Without pressing it, the user will not be able to rotate the handle to the full HOT position – as an anti-scald prevention mechanism. The anti-scald temperature stop ring should be fitted tightly over the valve (tapping using a rubber mallet might be required) for it to function properly.VALVE INSTALLATION -As the valve is installed, care should be taken to maintain a proper distance from the back of the valve to the finished tile which should be between 2.77″ and 3.44″ inches [Rough In Spec]. Also, the value must be installed straight and not at an angle or upside down. In case, the tile is thicker or valve installed in the wall is too deep, extension kits are available and can be used for elongating both handles of the valve.CUT OUT DIMENSIONS – The cut out in wall should be 7.89″ x 1.89″ Inches which is properly covered by the trim plate. This will ensure that the trim plate will cover the cut out hole in the wall.TRIMS – The trims comprise of a well-finished cover plate and handle knobs. The trim plate is used to cover the wall. Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower handles.CARTRIDGE – The TVH.2717F valve can be used with two cartridges. The default cartridge that the valve comes with is the Model # 15109 cartridge which is a 2 output non-shared [CAL-Green Compliant] cartridge. A shared port operation cartridge [Model # 15103] can also be used to activate 2 ports at the same time. Collection Serie 230 Style Transitional Warranty Limited Lifetime Warranty. See Warranty page for complete details. Available Finishes: Model# Finish List Price (USD) 230.2740CP Chrome USD1,239.00 230.2740MB Matte Black USD1,294.00 230.2740SB Satin Brass PVD USD1,294.00
$1,239.00
3/4" Horizontal Thermostatic Shower Valve & Trim - 1 - Output
The 2720 series of products from Flusso use the TVH.2693 Thermostatic valve which features 3/4″ NPT connections and has one water output. The right handle sets the temperature. The left handle controls water volume.HORIZONTAL OR VERTICAL INSTALLATION – The TVH.2693 can be installed horizontally or vertically.SUPPLY STOPS – There are two safety stops at each water inlet to prevent water flow in case of installation and repairs.HANDLE OPERATION – The right handle is used to control the temperature of water flowing through the outlet ports. The left handle is used to turn water on and off and can control the volume of water from full flow to a trickle.ANTI-SCALD RING – Over the temperature control knob, is an anti-scald temperature stop ring which is a safety feature in this thermostatic value. With the help of this ring, the temperature of the water is regulated. Covering this ring is the handle knob which has a push-button on the side. To adjust the water temperature, one needs to press this button and move the handle to a hot or cold direction. Without pressing it, the user will not be able to rotate the handle to the full HOT position – as an anti-scald prevention mechanism. The anti-scald temperature stop ring should be fitted tightly over the valve (tapping using a rubber mallet might be required) for it to function properly.VALVE INSTALLATION -As the valve is installed, care should be taken to maintain a proper distance from the back of the valve to the finished tile which should be between 2.77″ and 3.44″ inches [Rough In Spec]. Also, the value must be installed straight and not at an angle or upside down. In case, the tile is thicker, or valve installed in the wall is too deep, extension kits are available and can be used for elongating both handles of the valve.CUT OUT DIMENSIONS – The cut out in wall should be 7.89″ x 1.89″ Inches which is properly covered by the trim plate. This will ensure that the trim plate will cover the cut-out hole in the wall.TRIMS – The trims comprise of a well-finished cover plate and handle knobs. The trim plate is used to cover the wall. Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower handles. Collection Serie 230 Style Transitional Warranty Limited Lifetime Warranty. See Warranty page for complete details. Available Finishes: Model# Finish List Price (USD) 230.2720CP Chrome USD1,072.00 230.2720MB Matte Black USD1,128.00 230.2720SB Satin Brass PVD USD1,128.00
$1,072.00
3/4" Horizontal Thermostatic Shower Valve & Trim - 2 Output
The TVH.2717F Thermostatic valve features 3/4″ NPT connections and has 2 water outputs [ports] which are operable one at a time without shared port operation. This product meets CAL-Green compliance criteria. The right handle sets the temperature. The left handle controls water diversion between the 2 water output ports. Each port has full volume control capability.HORIZONTAL OR VERTICAL INSTALLATION – The TVH.2717F can be installed horizontally or vertically.SUPPLY STOPS – There are two safety stops at each water inlet to prevent water flow in case of installation and repairs.HANDLE OPERATION – The right handle is used to control the temperature of water flowing through the outlet ports. The left handle is used to divert the water between each output port and is= capable of controlling the volume of water from full flow to a trickle.ANTI-SCALD RING – Over the temperature control knob, is an anti-scald temperature stop ring which is a safety feature in this thermostatic value. With the help of this ring, the temperature of the water is regulated. Covering this ring is the handle knob which has a push-button on the side. In order to adjust the water temperature, one needs to press this button and move the handle to a hot or cold direction. Without pressing it, the user will not be able to rotate the handle to the full HOT position – as an anti-scald prevention mechanism. The anti-scald temperature stop ring should be fitted tightly over the valve (tapping using a rubber mallet might be required) for it to function properly.VALVE INSTALLATION -As the valve is installed, care should be taken to maintain a proper distance from the back of the valve to the finished tile which should be between 2.77″ and 3.44″ inches [Rough In Spec]. Also, the value must be installed straight and not at an angle or upside down. In case, the tile is thicker or valve installed in the wall is too deep, extension kits are available and can be used for elongating both handles of the valve.CUT OUT DIMENSIONS – The cut out in wall should be 7.89″ x 1.89″ Inches which is properly covered by the trim plate. This will ensure that the trim plate will cover the cut out hole in the wall.TRIMS – The trims comprise of a well-finished cover plate and handle knobs. The trim plate is used to cover the wall. Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower handles.CARTRIDGE – The TVH.2717F valve can be used with two cartridges. The default cartridge that the valve comes with is the Model # 15109 cartridge which is a 2 output non-shared [CAL-Green Compliant] cartridge. A shared port operation cartridge [Model # 15103] can also be used to activate 2 ports at the same time. Collection Serie 230 Style Transitional Warranty Limited Lifetime Warranty. See Warranty page for complete details. Available Finishes: Model# Finish List Price (USD) 230.2717CP Chrome USD1,239.00 230.2717MB Matte Black USD1,294.00 230.2717SB Satin Brass PVD USD1,294.00
$1,239.00
3/4" Horizontal Thermostatic Shower Valve & Trim - 3 Output
The TVH.2705F Thermostatic valve features 3/4″ NPT connections and has 3 water outputs [ports] which are operable one at a time without shared port operation. This product meets CAL-Green compliance criteria. The right handle sets the temperature. The left handle controls water diversion between the 3 water output ports. Each port has full volume control capability.HORIZONTAL OR VERTICAL INSTALLATION – The TVH.2705F can be installed horizontally or vertically.SUPPLY STOPS – There are two safety stops at each water inlet to prevent water flow in case of installation and repairs.HANDLE OPERATION – The right handle is used to control the temperature of water flowing through the outlet ports. The left handle is used to divert the water between each output port and is= capable of controlling the volume of water from full flow to a trickle.ANTI-SCALD RING – Over the temperature control knob, is an anti-scald temperature stop ring which is a safety feature in this thermostatic value. With the help of this ring, the temperature of the water is regulated. Covering this ring is the handle knob which has a push-button on the side. To adjust the water temperature, one needs to press this button and move the handle to a hot or cold direction. Without pressing it, the user will not be able to rotate the handle to the full HOT position – as an anti-scald prevention mechanism. The anti-scald temperature stop ring should be fitted tightly over the valve (tapping using a rubber mallet might be required) for it to function properly.VALVE INSTALLATION -As the valve is installed, care should be taken to maintain a proper distance from the back of the valve to the finished tile which should be between 2.77″ and 3.44″ inches [Rough In Spec]. Also, the value must be installed straight and not at an angle or upside down. In case, the tile is thicker, or valve installed in the wall is too deep, extension kits are available and can be used for elongating both handles of the valve.CUT OUT DIMENSIONS – The cut out in wall should be 7.89″ x 1.89″ Inches which is properly covered by the trim plate. This will ensure that the trim plate will cover the cut-out hole in the wall.TRIMS – The trims comprise of a well-finished cover plate and handle knobs. The trim plate is used to cover the wall. Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower handles.CARTRIDGE – The TVH.2705F valve can be used with two cartridges. The default cartridge that the valve comes with is the Model # 15100 cartridge which is a 3 output non-shared [CAL-Green Compliant] cartridge. A shared port operation cartridge [Model # 15200] can also be used to activate 2 out of 3 ports at the same time. Collection Serie 230 Style Transitional Warranty Limited Lifetime Warranty. See Warranty page for complete details. Available Finishes: Model# Finish List Price (USD) 230.2705CP Chrome USD1,239.00 230.2705MB Matte Black USD1,294.00 230.2705SB Satin Brass PVD USD1,294.00
$1,239.00
