Filters
2512 products viewed
Filters
3/4" Thermostatic Valve and Trim - 2 Outputs
The TVH.4401 Thermostatic valve features 3/4" NPT connections and has 2 water outputs [ports] which are operable simultaneously, i.e. both at the same time, or one at a time. The middle handle sets the temperature. The top handle controls output port 1 and the bottom handle controls output port 2. Each port has full volume control capability and can be activated at the same time.SUPPLY STOPS – There are two safety stops at each water inlet to prevent water flow in case of installation and repairs.HANDLE OPERATION – The middle handle is used to control the temperature of water flowing through the outlet. The top handle controls the volume of water from full flow to a trickle for the output port 1. The bottom handle controls the volume of water from full flow to a trickle for the output port 2.ANTI-SCALD RING – Over the temperature control knob, is an anti-scald temperature stop ring which is a safety feature in this thermostatic value. With the help of this ring, the temperature of the water is regulated. Covering this ring is the handle knob which has a push-button on the side. To adjust the water temperature, one needs to press this button and move the handle to a hot or cold direction. Without pressing it, the user will not be able to rotate the handle to the full hot position, as an anti-scald prevention mechanism. The anti-scald temperature stop ring should be fitted tightly over the valve (tapping using a rubber mallet might be required) for it to function properly.VALVE INSTALLATION – As the valve is installed, care should be taken to maintain a proper distance from the back of the valve to the finished tile which should be between 2.77 and 3.44 inches [Rough In Spec]. Also, the value must be installed straight and not at an angle or upside down. In case, the tile is thicker, or valve installed in the wall is too deep, extension kits are available and can be used for elongating both handles of the valve.CUT OUT DIMENSIONS – The cut out in wall should be 8.81 X 4.44 Inches which is properly covered by the trim plate. This will ensure that the trim plate will cover the cut-out hole in the wall.TRIMS – The trims comprise of a well-finished cover plate and handle knobs. The trim plate is used to cover the wall. Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower handles. Collection Serie 150 Style Contemporary / Modern Warranty Limited Lifetime Warranty. See Warranty page for complete details. Available Finishes: Model# Finish List Price (USD) 150.4401CP Chrome USD1,201.00
$1,201.00
3/4" Thermostatic Valve With Trim
The TVH.4201 is a ¾” Thermostatic valve with NPT female connections. It has two inlets with integral stop kits and single output. The valve has a flow rate of 13.0 GPM @ 60 PSI. The TVH.4201 does not have water turn off capability and thus must be used with a volume control or diverter valve.Supply Stops - There are two safety stops at each water inlet to prevent water flow in case of installation and repairs.Handle Operation - The handle is used to control temperature of water flowing through the outlet. This handle does not control the volume of water flowing through the valve.As the valve is installed, care should be taken to maintain proper distance from the back of the valve to the surface of finished tile which should be between 2.77” and 3.44”. Also, the valve must be installed vertical and not at an angle. In case, the tile is thicker, or wall is deep, extensions are used for elongating both handles of the valve to ensure proper setting of the trim (length of extensions for TVH.4201 valve is 1.40”). Extension kits comprises of thermostatic handle extension, which can be ordered separately in chrome, brushed nickel, or other special finishes.Cut Out Dimensions - The cut out in wall should be 2.67” X 4.44” which is properly covered by the trim plate. This will ensure that the trim plate will cover the cut-out hole in the wall.Trims - The trims comprise of well finished trim plate and handle. The trim plate is used to cover the wall and has markings for HOT/COLD for temperature control handle. Over the temperature control knob, is an anti-scald temperature stop ring which is a safety feature in this thermostatic value. With the help of this ring, temperature of the water is regulated. Covering this ring is the handle knob which has a push button on the side. To adjust the water temperature, one needs to press this button and move the handle to hot or cold direction. Without pressing it, the user will not be able to rotate the handle to the full HOT position – as an anti-scald prevention mechanism. The anti-scald temperature stop ring should be fitted tightly over the valve (tapping using a rubber mallet might be required during installation) for it to function properly.Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower handles. Collection Serie 100 Style Contemporary / Modern Warranty Limited Lifetime Warranty. See Warranty page for complete details. Available Finishes: Model# Finish List Price (USD) 100.4201CP Chrome USD585.00 100.4201BN Brushed Nickel PVD USD612.00 100.4201MB Matte Black USD624.00 100.4201SB Satin Brass PVD USD624.00 100.4201BB Brushed Bronze PVD USD624.00 100.4201DT Dark Tan USD703.00 100.4201DGR Dark Green USD703.00 100.4201RG Rock Grey USD703.00 100.4201LT Light Tan USD703.00 100.4201IG Flusso Green USD703.00 100.4201VB Vortex Brown USD703.00 100.4201DR Deep Red USD703.00 100.4201LV Light Verde USD703.00 100.4201AG Army Green USD703.00 100.4201DG Dark Grey USD703.00 100.4201LG Leaf Green USD703.00 100.4201NB Navy Blue USD703.00 100.4201GB Gloss Black USD703.00 100.4201BP Blue Platinum USD703.00 100.4201SKB Sky Blue USD703.00 100.4201CR Crimson USD703.00 100.4201GMG Gun Metal Grey USD703.00 100.4201SG Steel Grey USD703.00
$585.00
3/4" Thermostatic Valve With Trim
The TVH.4201 is a ¾” Thermostatic valve with NPT female connections. It has two inlets with integral stop kits and single output. The valve has a flow rate of 13.0 GPM @ 60 PSI. The TVH.4201 does not have water turn off capability and thus must be used with a volume control or diverter valve.Supply Stops - There are two safety stops at each water inlet to prevent water flow in case of installation and repairs.Handle Operation - The handle is used to control temperature of water flowing through the outlet. This handle does not control the volume of water flowing through the valve.As the valve is installed, care should be taken to maintain proper distance from the back of the valve to the surface of finished tile which should be between 2.77” and 3.44”. Also, the valve must be installed vertical and not at an angle. In case, the tile is thicker, or wall is deep, extensions are used for elongating both handles of the valve to ensure proper setting of the trim (length of extensions for TVH.4201 valve is 1.40”). Extension kits comprises of thermostatic handle extension, which can be ordered separately in chrome, brushed nickel, or other special finishes.Cut Out Dimensions - The cut out in wall should be 2.67” X 4.44” which is properly covered by the trim plate. This will ensure that the trim plate will cover the cut-out hole in the wall.Trims - The trims comprise of well finished trim plate and handle. The trim plate is used to cover the wall and has markings for HOT/COLD for temperature control handle. Over the temperature control knob, is an anti-scald temperature stop ring which is a safety feature in this thermostatic value. With the help of this ring, temperature of the water is regulated. Covering this ring is the handle knob which has a push button on the side. To adjust the water temperature, one needs to press this button and move the handle to hot or cold direction. Without pressing it, the user will not be able to rotate the handle to the full HOT position – as an anti-scald prevention mechanism. The anti-scald temperature stop ring should be fitted tightly over the valve (tapping using a rubber mallet might be required during installation) for it to function properly.Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower handles. Collection Serie 145 Style Contemporary / Modern Warranty Limited Lifetime Warranty. See Warranty page for complete details. Available Finishes: Model# Finish List Price (USD) 145.4201CP Chrome USD654.00 145.4201MB Matte Black USD689.00 145.4201SB Satin Brass PVD USD682.00 Product Docs: Spec Sheet Parts Diagram Installation Docs Installation Video Product Info: Connection Size 3/4" Female Integrated Volume Control Yes Valve Included Yes Valve Type Thermostatic Installation Type Wall Mounted Extensions Available Yes Material Brass Anti-Scald Ring Included Supply Stops Included Temperature Cartridge TVH.4201-9853 Flow Rate 13 GPM @ 60 PSI Handle Style Knob
$654.00
3/4" Thermostatic Valve With Trim
The TVH.4201 is a ¾” Thermostatic valve with NPT female connections. It has two inlets with integral stop kits and single output. The valve has a flow rate of 13.0 GPM @ 60 PSI. The TVH.4201 does not have water turn off capability and thus must be used with a volume control or diverter valve.Supply Stops - There are two safety stops at each water inlet to prevent water flow in case of installation and repairs.Handle Operation - The handle is used to control temperature of water flowing through the outlet. This handle does not control the volume of water flowing through the valve.As the valve is installed, care should be taken to maintain proper distance from the back of the valve to the surface of finished tile which should be between 2.77” and 3.44”. Also, the valve must be installed vertical and not at an angle. In case, the tile is thicker, or wall is deep, extensions are used for elongating both handles of the valve to ensure proper setting of the trim (length of extensions for TVH.4201 valve is 1.40”). Extension kits comprises of thermostatic handle extension, which can be ordered separately in chrome, brushed nickel, or other special finishes.Cut Out Dimensions - The cut out in wall should be 2.67” X 4.44” which is properly covered by the trim plate. This will ensure that the trim plate will cover the cut-out hole in the wall.Trims - The trims comprise of well finished trim plate and handle. The trim plate is used to cover the wall and has markings for HOT/COLD for temperature control handle. Over the temperature control knob, is an anti-scald temperature stop ring which is a safety feature in this thermostatic value. With the help of this ring, temperature of the water is regulated. Covering this ring is the handle knob which has a push button on the side. To adjust the water temperature, one needs to press this button and move the handle to hot or cold direction. Without pressing it, the user will not be able to rotate the handle to the full HOT position – as an anti-scald prevention mechanism. The anti-scald temperature stop ring should be fitted tightly over the valve (tapping using a rubber mallet might be required during installation) for it to function properly.Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower handles. Collection Serie 150 Style Contemporary / Modern Warranty Limited Lifetime Warranty. See Warranty page for complete details. Available Finishes: Model# Finish List Price (USD) 150.4201CP Chrome USD701.00
$701.00
3/4" Thermostatic Valve With Trim
The TVH.4201 is a ¾” Thermostatic valve with NPT female connections. It has two inlets with integral stop kits and single output. The valve has a flow rate of 13.0 GPM @ 60 PSI. The TVH.4201 does not have water turn off capability and thus must be used with a volume control or diverter valve.Supply Stops - There are two safety stops at each water inlet to prevent water flow in case of installation and repairs.Handle Operation - The handle is used to control temperature of water flowing through the outlet. This handle does not control the volume of water flowing through the valve.As the valve is installed, care should be taken to maintain proper distance from the back of the valve to the surface of finished tile which should be between 2.77” and 3.44”. Also, the valve must be installed vertical and not at an angle. In case, the tile is thicker, or wall is deep, extensions are used for elongating both handles of the valve to ensure proper setting of the trim (length of extensions for TVH.4201 valve is 1.40”). Extension kits comprises of thermostatic handle extension, which can be ordered separately in chrome, brushed nickel, or other special finishes.Cut Out Dimensions - The cut out in wall should be 2.67” X 4.44” which is properly covered by the trim plate. This will ensure that the trim plate will cover the cut-out hole in the wall.Trims - The trims comprise of well finished trim plate and handle. The trim plate is used to cover the wall and has markings for HOT/COLD for temperature control handle. Over the temperature control knob, is an anti-scald temperature stop ring which is a safety feature in this thermostatic value. With the help of this ring, temperature of the water is regulated. Covering this ring is the handle knob which has a push button on the side. To adjust the water temperature, one needs to press this button and move the handle to hot or cold direction. Without pressing it, the user will not be able to rotate the handle to the full HOT position – as an anti-scald prevention mechanism. The anti-scald temperature stop ring should be fitted tightly over the valve (tapping using a rubber mallet might be required during installation) for it to function properly.Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower handles. Collection Serie 160 Style Contemporary / Modern Warranty Limited Lifetime Warranty. See Warranty page for complete details. Available Finishes: Model# Finish List Price (USD) 160.4201CP Chrome USD701.00 160.4201BN Brushed Nickel PVD USD746.00 160.4201PN Polished Nickel PVD USD746.00 160.4201MB Matte Black USD746.00
$701.00
3/4" Thermostatic Valve With Trim
The TVH.4201 is a ¾” Thermostatic valve with NPT female connections. It has two inlets with integral stop kits and single output. The valve has a flow rate of 13.0 GPM @ 60 PSI. The TVH.4201 does not have water turn off capability and thus must be used with a volume control or diverter valve.Supply Stops - There are two safety stops at each water inlet to prevent water flow in case of installation and repairs.Handle Operation - The handle is used to control temperature of water flowing through the outlet. This handle does not control the volume of water flowing through the valve.As the valve is installed, care should be taken to maintain proper distance from the back of the valve to the surface of finished tile which should be between 2.77” and 3.44”. Also, the valve must be installed vertical and not at an angle. In case, the tile is thicker, or wall is deep, extensions are used for elongating both handles of the valve to ensure proper setting of the trim (length of extensions for TVH.4201 valve is 1.40”). Extension kits comprises of thermostatic handle extension, which can be ordered separately in chrome, brushed nickel, or other special finishes.Cut Out Dimensions - The cut out in wall should be 2.67” X 4.44” which is properly covered by the trim plate. This will ensure that the trim plate will cover the cut-out hole in the wall.Trims - The trims comprise of well finished trim plate and handle. The trim plate is used to cover the wall and has markings for HOT/COLD for temperature control handle. Over the temperature control knob, is an anti-scald temperature stop ring which is a safety feature in this thermostatic value. With the help of this ring, temperature of the water is regulated. Covering this ring is the handle knob which has a push button on the side. To adjust the water temperature, one needs to press this button and move the handle to hot or cold direction. Without pressing it, the user will not be able to rotate the handle to the full HOT position – as an anti-scald prevention mechanism. The anti-scald temperature stop ring should be fitted tightly over the valve (tapping using a rubber mallet might be required during installation) for it to function properly.Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower handles. Collection Serie 196 Style Contemporary / Modern Warranty Limited Lifetime Warranty. See Warranty page for complete details. Available Finishes: Model# Finish List Price (USD) 196.4201CP Chrome USD661.00 196.4201BN Brushed Nickel PVD USD714.00 196.4201PN Polished Nickel PVD USD714.00 196.4201MB Matte Black USD739.00 196.4201SB Satin Brass PVD USD727.00 196.4201DT Dark Tan USD970.00 196.4201DGR Dark Green USD970.00 196.4201RG Rock Grey USD970.00 196.4201LT Light Tan USD970.00 196.4201IG Flusso Green USD970.00 196.4201VB Vortex Brown USD970.00 196.4201DR Deep Red USD970.00 196.4201LV Light Verde USD970.00 196.4201AG Army Green USD970.00 196.4201DG Dark Grey USD970.00 196.4201LG Leaf Green USD970.00 196.4201NB Navy Blue USD970.00 196.4201GB Gloss Black USD970.00 196.4201BP Blue Platinum USD970.00 196.4201SKB Sky Blue USD970.00 196.4201CR Crimson USD970.00 196.4201GMG Gun Metal Grey USD970.00 196.4201SG Steel Grey USD970.00
$661.00
3/4" Thermostatic Valve With Trim
The TVH.4201 is a ¾” Thermostatic valve with NPT female connections. It has two inlets with integral stop kits and single output. The valve has a flow rate of 13.0 GPM @ 60 PSI. The TVH.4201 does not have water turn off capability and thus must be used with a volume control or diverter valve.Supply Stops - There are two safety stops at each water inlet to prevent water flow in case of installation and repairs.Handle Operation - The handle is used to control temperature of water flowing through the outlet. This handle does not control the volume of water flowing through the valve.As the valve is installed, care should be taken to maintain proper distance from the back of the valve to the surface of finished tile which should be between 2.77” and 3.44”. Also, the valve must be installed vertical and not at an angle. In case, the tile is thicker, or wall is deep, extensions are used for elongating both handles of the valve to ensure proper setting of the trim (length of extensions for TVH.4201 valve is 1.40”). Extension kits comprises of thermostatic handle extension, which can be ordered separately in chrome, brushed nickel, or other special finishes.Cut Out Dimensions - The cut out in wall should be 2.67” X 4.44” which is properly covered by the trim plate. This will ensure that the trim plate will cover the cut-out hole in the wall.Trims - The trims comprise of well finished trim plate and handle. The trim plate is used to cover the wall and has markings for HOT/COLD for temperature control handle. Over the temperature control knob, is an anti-scald temperature stop ring which is a safety feature in this thermostatic value. With the help of this ring, temperature of the water is regulated. Covering this ring is the handle knob which has a push button on the side. To adjust the water temperature, one needs to press this button and move the handle to hot or cold direction. Without pressing it, the user will not be able to rotate the handle to the full HOT position – as an anti-scald prevention mechanism. The anti-scald temperature stop ring should be fitted tightly over the valve (tapping using a rubber mallet might be required during installation) for it to function properly.Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower handles. Collection Serie 230 Style Transitional Warranty Limited Lifetime Warranty. See Warranty page for complete details. Available Finishes: Model# Finish List Price (USD) 230.4201CP Chrome USD704.00 230.4201MB Matte Black USD773.00 230.4201SB Satin Brass PVD USD773.00
$704.00
3/4" Thermostatic Valve With Trim
The TVH.4201 is a ¾” Thermostatic valve with NPT female connections. It has two inlets with integral stop kits and single output. The valve has a flow rate of 13.0 GPM @ 60 PSI. The TVH.4201 does not have water turn off capability and thus must be used with a volume control or diverter valve.Supply Stops - There are two safety stops at each water inlet to prevent water flow in case of installation and repairs.Handle Operation - The handle is used to control temperature of water flowing through the outlet. This handle does not control the volume of water flowing through the valve.As the valve is installed, care should be taken to maintain proper distance from the back of the valve to the surface of finished tile which should be between 2.77” and 3.44”. Also, the valve must be installed vertical and not at an angle. In case, the tile is thicker, or wall is deep, extensions are used for elongating both handles of the valve to ensure proper setting of the trim (length of extensions for TVH.4201 valve is 1.40”). Extension kits comprises of thermostatic handle extension, which can be ordered separately in chrome, brushed nickel, or other special finishes.Cut Out Dimensions - The cut out in wall should be 2.67” X 4.44” which is properly covered by the trim plate. This will ensure that the trim plate will cover the cut-out hole in the wall.Trims - The trims comprise of well finished trim plate and handle. The trim plate is used to cover the wall and has markings for HOT/COLD for temperature control handle. Over the temperature control knob, is an anti-scald temperature stop ring which is a safety feature in this thermostatic value. With the help of this ring, temperature of the water is regulated. Covering this ring is the handle knob which has a push button on the side. To adjust the water temperature, one needs to press this button and move the handle to hot or cold direction. Without pressing it, the user will not be able to rotate the handle to the full HOT position – as an anti-scald prevention mechanism. The anti-scald temperature stop ring should be fitted tightly over the valve (tapping using a rubber mallet might be required during installation) for it to function properly.Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower handles. Collection Serie 260 Style Contemporary / Modern Warranty Limited Lifetime Warranty. See Warranty page for complete details. Available Finishes: Model# Finish List Price (USD) 260.4201CP Chrome USD650.00 260.4201BN Brushed Nickel PVD USD675.00 260.4201PN Polished Nickel PVD USD675.00 260.4201MB Matte Black USD714.00 260.4201SB Satin Brass PVD USD714.00 260.4201BB Brushed Bronze PVD USD714.00 260.4201LV Light Verde USD823.00 260.4201SG Steel Grey USD823.00 260.4201DT Dark Tan USD823.00 260.4201DGR Dark Green USD823.00 260.4201RG Rock Grey USD823.00 260.4201LT Light Tan USD823.00 260.4201IG Flusso Green USD823.00 260.4201VB Vortex Brown USD823.00 260.4201DR Deep Red USD823.00 260.4201GMG Gun Metal Grey USD823.00 260.4201AG Army Green USD823.00 260.4201DG Dark Grey USD823.00 260.4201LG Leaf Green USD823.00 260.4201NB Navy Blue USD823.00 260.4201GB Gloss Black USD823.00 260.4201BP Blue Platinum USD823.00 260.4201SKB Sky Blue USD823.00 260.4201CR Crimson USD823.00
$650.00
